LED Linear High Bay vs UFO High Bay: Warehouse Lighting Showdown
SH-E01 LED linear high bay light — aluminum alloy housing, IP65 protection, 5-year warranty.
Direct answer: The SH-E01 LED linear high bay and the HL-E01 UFO LED high bay are both ceiling-mounted fixtures for warehouses, factories and similar high-ceiling spaces, but they are built for different site conditions. The SH-E01 is the protective, layout-driven option: IP65, a 5-year warranty, an aluminum alloy housing with a PC/PMMA lens, a 90° (H) × 120° (V) beam angle, and a choice of surface mounting or chain/cable suspension. The HL-E01 is the output-driven option: up to 210 lm/W, 100–240W, 185–265V or 100–265V input, 6KV surge protection, and an optional motion sensor. Choose the linear fixture for harsh industrial settings, workshops and structured aisle layouts; choose the UFO fixture for warehouses, factories, retail spaces and gyms where output per fixture and voltage tolerance matter most.
The two models differ on almost every dimension a buyer has to sign off on: form factor, light distribution, housing and optics, ingress protection, warranty, power range, luminous efficacy, input voltage, surge protection, wiring and mounting method. This comparison puts the two datasheets side by side and then translates each difference into a site decision.
Why “Which High Bay Is Better?” Is the Wrong Question
The linear-versus-UFO question usually arrives late in a procurement process, after two quotations are already on the table. Both documents list wattages, colour temperatures and fixture quantities, and both look technically similar. The differences that actually decide a project sit further down the page.
A high bay installation is judged at handover on five points: whether illumination covers the working area evenly, whether the fixture survives the environment around it, whether it can be fixed to the structure that actually exists above the floor, whether the electrical supply stays inside the fixture's tolerance, and how long it runs before someone has to bring a lift in and replace it. Linear high bays and UFO high bays answer those five questions differently, which is why no single fixture wins on all counts.
The practical decision order is therefore: environment and mounting first, output and efficacy second, commercial terms last. A fixture that is wrong on ingress protection or mounting method does not perform “slightly worse” — it fails inspection or slows down installation.
Where These Two Fixtures Come From
Zhejiang Lepeng Electric Appliance Co.,Ltd. is a Chinese LED lamp and luminaire manufacturer founded in 2009, headquartered in the Baiguan Industrial Zone of Shangyu, Zhejiang Province, with two additional production bases in Qiandaohu, Zhejiang and Jingdezhen, Jiangxi. The company operates a 200,000 m² manufacturing footprint with 2,000 employees, including a 200-person R&D team, and reports a monthly capacity of 45 million LED lamps and 5 million LED luminaires. Around 90% of production is exported to the EU, Southeast Asia, the Middle East and Latin America. The company sells under its own MKOPTO brand and also runs OEM and ODM programmes for global clients. Both the SH-E01 and the HL-E01 sit inside that portfolio.
The category context explains why specification-level decisions matter more than brand-level ones. Fortune Business Insights values the global LED lighting market at USD 109.11 billion in 2025 and projects it to reach USD 336.90 billion by 2034. Grand View Research estimates the global commercial lighting market at USD 47.54 billion in 2024, with LED products already holding a 58.1% revenue share of that segment. OEC data shows China exported USD 31.4 billion of light fixtures in 2024, equal to 59.3% of total global exports. Supply is deep, and buyers can source high bays from many factories — so the fixture that fits the site is the differentiator, not the availability of a supplier.
Headquarters and production base, Zhejiang — the same manufacturing operation produces both the SH-E01 and the HL-E01.
The Contenders in Detail
SH-E01 — LED Linear High Bay Light
The SH-E01 is an LED linear high bay light built for warehouse and factory ceilings, using an aluminum alloy housing with a PC/PMMA lens. It is offered in 50W, 100W, 150W and 200W versions, with luminous efficacy options of 100, 135 and 150 lm/W and a beam angle of 90° (H) × 120° (V). Colour temperature options are 3000K, 4000K, 5000K and 6500K. The linear body comes in three lengths — 305.6×97.3×68.1 mm, 580.6×97.3×68.1 mm and 855.6×97.3×68.1 mm — so a continuous run can be planned to match the length of an aisle or a work zone.
Three specification points carry the most weight in evaluation. First, the fixture is IP65 rated, which addresses dust and water ingress in non-conditioned industrial environments. Second, it carries a 5-year warranty and uses a high-quality branded driver, which changes how replacement cycles are planned across the early years of a project. Third, it supports two mounting approaches — a mounting kit for surface installation, or chain/cable suspension — which gives the installer a fallback when the ceiling structure does not suit a single method. Wiring is simplified by a one-piece connector design.
HL-E01 — UFO LED High Bay Light
The HL-E01 is a round, UFO-style LED high bay light built on a die-cast aluminum body with a hollow heat dissipation structure and a PC lens. Power options are 100W, 150W, 200W and 240W, with efficacy options of 140, 160, 185 and 210 lm/W. Colour temperature options are 4000K, 5000K and 6500K. Its intended applications are warehouses, factories, retail spaces and gyms.
Its differentiating hardware is electrical. The fixture is supplied with either 185–265V or 100–265V input, giving a wider usable voltage band for sites where supply stability is a concern, and it carries 6KV surge protection. It uses premium Sosen and Moso power supplies, and arrives pre-wired to the power supply with a 3×1.0 mm² cable and 300 mm exposed leads, which shortens connection time on site. An optional motion sensor is available, with a smooth 3-second brightness transition when the sensor triggers. The design is also described as easy to maintain, which matters when luminaires sit above racking or production equipment.
HL-E01 UFO LED high bay light — die-cast aluminum body, up to 210 lm/W, 6KV surge protection.
SH-E01 vs HL-E01: Specification Comparison
| Parameter | SH-E01 (LED Linear High Bay) | HL-E01 (UFO LED High Bay) |
|---|---|---|
| Fixture type | LED linear high bay light for warehouse & factory | UFO LED high bay light |
| Power options | 50 / 100 / 150 / 200W | 100 / 150 / 200 / 240W |
| Luminous efficacy | 100 / 135 / 150 lm/W | 140 / 160 / 185 / 210 lm/W |
| Beam angle | 90° (H) × 120° (V) | — |
| CCT options | 3000K / 4000K / 5000K / 6500K | 4000K / 5000K / 6500K |
| Housing & optics | Aluminum alloy housing + PC/PMMA lens | Die-cast aluminum body + PC lens |
| Thermal design | — | Hollow heat dissipation structure |
| Power supply | High-quality branded driver | Premium Sosen and Moso power supplies |
| Input voltage | — | 185–265V or 100–265V |
| Surge protection | — | 6KV |
| Ingress protection | IP65 | — |
| Warranty | 5 years | — |
| Wiring | One-piece connector design | 3×1.0 mm² cable, 300 mm exposed leads, pre-wired to power supply |
| Mounting | Mounting kit for surface installation, or chain/cable suspension | — |
| Sensor option | — | Optional motion sensor with 3-second brightness transition |
| Body dimensions | 305.6×97.3×68.1 mm / 580.6×97.3×68.1 mm / 855.6×97.3×68.1 mm | — |
| Typical applications | Warehouses, factories, workshops | Warehouses, factories, retail spaces, gyms |
“—” indicates that the value is not stated in the published specification for that model. Confirm the required value with the supplier against your site conditions before ordering.
What Each Difference Means on Site
Form factor and light distribution
The SH-E01 is a long linear body available in three lengths, with a 90° (H) × 120° (V) beam. That geometry suits spaces organised in rows — racking aisles, work benches, production lines and long corridors — because fixtures can be aligned with the layout rather than positioned point by point. The HL-E01 is a compact round UFO body, which simplifies mounting-point planning in open floor areas where fixtures are distributed across a grid instead of along lines.
Housing, optics and thermal path
Both fixtures use aluminium bodies, but they are described differently in the datasheets. The SH-E01 pairs an aluminum alloy housing with a PC/PMMA lens. The HL-E01 uses a die-cast aluminum body with a hollow heat dissipation structure and a PC lens. For sites running fixtures at continuous high output, an explicitly engineered heat path is a design point worth checking against the operating hours the space will run.
Ingress protection and warranty planning
Ingress protection is the clearest divider in this comparison. The SH-E01 states IP65, which covers dust and water protection and makes it the more suitable of the two for harsh industrial environments, workshops, and buildings where humidity, airborne dust or cleaning activity is part of daily operation. The same fixture states a 5-year warranty, and the warranty period feeds directly into how a project plans replacement cycles and maintenance budgets over the first years of operation. Where an ingress protection rating is a written project requirement, the SH-E01 is the model to specify, and buyers should confirm the required protection level for any fixture against their actual site conditions.
Power, efficacy and electrical tolerance
The power ranges overlap but do not match. The SH-E01 starts at 50W and stops at 200W, so it can serve lower-ceiling or smaller zones where a 100W minimum would be excessive. The HL-E01 starts at 100W and extends to 240W, which suits spaces where a single fixture has to deliver more output. On efficacy, the two bands are 100/135/150 lm/W for the SH-E01 and 140/160/185/210 lm/W for the HL-E01 — the higher band reduces the number of fixtures or the energy drawn for the same delivered output.
Electrically, the HL-E01 publishes 185–265V or 100–265V input, 6KV surge protection, and pre-wired 3×1.0 mm² cable with 300 mm exposed leads. Those three details matter in older industrial buildings and in regions where supply fluctuates: a wide voltage band reduces nuisance failures, surge protection addresses switching transients, and pre-wired leads reduce on-site connection time. The SH-E01 datasheet does not state a voltage band or surge figure — buyers specifying it for a site with unstable supply should confirm those values before the order.
Mounting, wiring and maintenance
Mounting flexibility is where the SH-E01 is unambiguous: it can be fixed with a mounting kit for surface installation or hung on chain/cable suspension, so the same model works whether the ceiling is a solid structure or an open truss. The one-piece connector design speeds wiring at the fixture. The HL-E01 arrives pre-wired to its power supply with a defined cable specification, which shifts the work from terminal-level wiring to the final connection, and its datasheet describes easy maintenance as a design feature. For the HL-E01, confirm the suspension hardware against the structure you actually have before the installation plan is frozen.
Step-by-Step: Matching the Model to Your Environment
- Measure the mounting height and map the layout. Record ceiling height and whether the space is organised in aisles, rows or an open grid. Rows and aisles favour linear fixtures that can be aligned with the layout; open grids favour evenly distributed compact fixtures.
- Classify the environment. Note dust, moisture, washdown, condensation and temperature swings. If the site needs a stated ingress protection rating, the SH-E01 is IP65 rated; if the space is dry and conditioned, protection level becomes a smaller factor.
- Set the target output. Compare the required output against the two efficacy bands — 100/135/150 lm/W on the SH-E01 and 140/160/185/210 lm/W on the HL-E01 — and the two power ranges, 50–200W and 100–240W, to decide which fixture carries the load.
- Check the electrical supply. If the supply is wide-ranging or transient-prone, the HL-E01's 185–265V or 100–265V input and 6KV surge protection are the relevant specifications. Confirm voltage band and surge exposure with the site electrician.
- Decide the mounting method. Surface mounting kit or chain/cable suspension covers most structures for the SH-E01. For the HL-E01, confirm the suspension hardware that fits the ceiling structure.
- Select the colour temperature. The SH-E01 covers 3000K, 4000K, 5000K and 6500K. If a warm 3000K appearance is required, only the linear range covers it; the HL-E01 range is 4000K, 5000K and 6500K.
- Plan sensing and control. For low-traffic areas, the HL-E01 optional motion sensor with a smooth 3-second brightness transition can reduce wasted run-hours.
- Confirm commercial and after-sales terms, then validate. OEM/ODM customisation of fixture appearance, power and accessories is supported, lead time is 30–45 days, and MOQ depends on the product. Validate the chosen model with a sample before releasing the full order.
Use Cases: Which Model Fits Which Space
Harsh industrial settings and workshops → SH-E01. IP65 protection, an aluminum alloy housing with a PC/PMMA lens, and a 5-year warranty make the linear fixture the fit where dust, humidity or cleaning activity is normal. Surface mounting or suspension covers both solid and open ceilings.
Warehouses and factories with high ceilings → HL-E01. Up to 210 lm/W and up to 240W per fixture concentrate output where fewer, higher-output luminaires are preferred, and the hollow heat dissipation structure supports continuous industrial operation.
Retail spaces and gyms → HL-E01. The 4000K, 5000K and 6500K options cover clean, neutral and cool presentations, and the optional motion sensor suits areas that are only intermittently occupied.
Aisles and structured racking → SH-E01. Three body lengths and a 90° (H) × 120° (V) beam allow fixture runs to follow racks and work zones instead of being scattered across them.
Sites with variable supply → HL-E01. Wide voltage input and 6KV surge protection target buildings where the supply is not tightly regulated.
Construction site and emergency lighting. Lepeng's product range covers warehouse and factory lighting, road and community landscape lighting, construction site and emergency lighting, and residential and commercial applications. Where temporary or outdoor site lighting is required alongside interior high bays, the FL-C01 Series outdoor LED floodlight covers 10–300W with 100–240V or 220–240V input, up to 120 lm/W efficiency, surge protection up to 2KV and a power factor above 0.9 in an aluminum and glass housing. Across these installations, the company reports client use in warehouse, factory, road, landscape and construction applications over a 5–10 year duration with stable operation.
Frequently Asked Questions
For a workshop with dust, humidity or regular cleaning, the SH-E01 LED linear high bay is the specification-led choice because it states an IP65 rating for dust and water protection, alongside a 5-year warranty and an aluminum alloy housing with a PC/PMMA lens. It also offers 50–200W power options, a 90° (H) × 120° (V) beam angle, and mounting either by surface mounting kit or by chain/cable suspension. Where the environment is dry and conditioned, the specification requirements are lower and both models can be considered on output and layout instead.
UL Solutions lists IEC 60598 for luminaires, UL 1598 as the Standard for Luminaires, and UL 8750 as the Standard for LED Equipment among the commonly referenced safety and performance standards for LED lighting. Which of these applies depends on the destination market and the project specification. Buyers should identify the applicable standard for the end market and request the corresponding documentation for the exact model, wattage and voltage variant before releasing the order, since the required evidence is model-specific.
The SH-E01 is covered by a 5-year warranty and uses a high-quality branded driver designed for long-term performance. In evaluation, warranty length defines how many replacement cycles a project should plan for within the first years of operation, and it interacts with mounting height: a fixture above racking is more expensive to service than one above an open floor. The HL-E01 datasheet does not state a warranty period, so buyers who require a defined warranty term on that model should confirm the terms with the supplier in writing before ordering.
Lead time is 30–45 days, and the minimum order quantity depends on the specific product. Lepeng supports OEM/ODM projects, with customisation available for fixture appearance, power and accessories, discussed per product during the enquiry stage. For projects that need a defined delivery schedule, confirming wattage, CCT, voltage variant and mounting configuration before the order is placed is what keeps the lead time predictable.
Yes. Alongside high bays, the product range covers LED floodlights, street lights, solar flood lights, solar street lights, garden lights, stadium lights, tri-proof lights, bulkhead lights, work lights, ceiling lights, panel lights and related commercial luminaires, with construction site and emergency lighting listed among the supported applications. For site lighting specifically, the FL-C01 Series outdoor LED floodlight covers 10–300W with 100–240V or 220–240V input, up to 120 lm/W efficiency, up to 2KV surge protection and a power factor above 0.9 in an aluminum and glass housing. Both high bays and floodlights come from the same manufacturing operation, so a mixed project can be specified and scheduled together. To move from comparison to a project-specific configuration, request a quotation or a sample through the contact details below.
Conclusion: Decide by Environment, Then by Output
The SH-E01 and the HL-E01 are not competing versions of the same answer. The SH-E01 LED linear high bay is the fixture for environments and layouts that demand protection and alignment: IP65, a 5-year warranty, an aluminum alloy housing with a PC/PMMA lens, 50–200W, 100/135/150 lm/W, three body lengths, a 90° (H) × 120° (V) beam, and a choice of surface mounting or chain/cable suspension. The HL-E01 UFO LED high bay is the fixture for output and electrical resilience: 100–240W, 140/160/185/210 lm/W, 185–265V or 100–265V input, 6KV surge protection, Sosen and Moso power supplies, pre-wired cable, and an optional motion sensor.
Work through the sequence in order — environment and ingress protection, layout and form factor, target output and efficacy, supply voltage and surge exposure, mounting method, colour temperature, sensing, then warranty and lead time. That sequence produces a specification a project can defend, and it removes the guesswork from a two-quotation decision.
Lead time is 30–45 days, OEM/ODM customisation is available, and MOQ depends on the product. Samples can be requested for validation before the full order.
Next step: sample, quotation or catalogue
Send your ceiling height, layout, environment and required voltage variant, and the team will confirm which model fits — or supply both for side-by-side validation.
Download the full product catalogue: Lepeng Electric product brochure (PDF)
Website: www.idealbright.com
Email: fish@idealbright.com | Tel: +86-575-82188752 | WhatsApp: +86-13777885334
Address: No. 1, Yueguo Road, Baiguan Industrial Park, Shangyu District, Shaoxing City, Zhejiang Province
High bay, flood light and commercial LED luminaires available from the same production base for project and volume orders.
Have Questions or Need More Details?
Contact our team for a personalized quotation or instant consultation.
Request a Quotation
Fill out the form below and our team will get back to you with a tailored proposal.
WhatsApp Direct Chat
Prefer to chat in real-time? Message us on WhatsApp for instant assistance & quick answers.
- Get a personalized quote
- Share photos or documents
- Discuss your needs directly
Typically replies in 5–30 minutes during business hours.