Two-stage compression
Lower stage compression ratio, reduced internal leakage and bearing load, higher volumetric efficiency and longer host life.
{{ variable.name }}
A two-stage permanent magnet variable frequency air compressor for factories that need stable pressure, lower energy costs and continuous duty. The 185 kW project case in Indonesia has been in service since 2020.

The 185 kW two-stage PM VSD air compressor is built for automated production lines that cannot tolerate pressure swings. Two-stage compression lowers the compression ratio at each stage, reduces internal leakage and bearing load, and supports a longer air-end service life. In the Indonesia project, one 185 kW unit has supplied pneumatic equipment, assembly lines, packaging machinery and instrument air for more than five years.
Lower stage compression ratio, reduced internal leakage and bearing load, higher volumetric efficiency and longer host life.
Two-stage PM VSD replaces single-stage compression and increases displacement by nearly 15%, adding up to 15% energy saving.
The rotor is refined by more than 20 procedures to ensure profile accuracy, reliability and effectiveness.
Compared with ordinary industrial frequency machines. At 8,000 h/year, the saving can reach about USD 30,000 per year.
The motor and male rotor use one shaft, eliminating coupling and gear transmission and reducing related failure risk.
No motor, bearing, gear or coupling noise; noise range for the series is 65–78 ±3 dB.
| Parameter | Specification |
|---|---|
| Model family | SLTT-22V, SLTT-30V, SLTT-37V, SLTT-45V, SLTT-55V, SLTT-75V, SLTT-90V, SLTT-110V, SLTT-132V, SLTT-160V, SLTT-185V, SLTT-220V, SLTT-250V |
| Project case power | 185 kW |
| Working pressure | 8–13 bar |
| Capacity | 1.36–53.68 m³/min (series range) |
| Power range | 22–250 kW |
| Horsepower | 30–335 hp |
| Noise | 65–78 ±3 dB |
| Air outlet pipe diameter | DN40, DN50, DN65, DN100 |
| Net weight | 732–6000 kg (series range) |
| Compression | Two-stage compression |
| Drive | Permanent magnet variable frequency drive |
| Rotor profile | Patented UV profile, refined by more than 20 procedures |
| Materials | Cast iron, stainless steel |
The SLTT-V series covers 13 models from SLTT-22V to SLTT-250V, with 22–250 kW power, 8–13 bar working pressure and 1.36–53.68 m³/min capacity range. The Indonesia case uses a 185 kW unit. Final model selection depends on required air flow, pressure, duty cycle and site conditions.
The air end uses a patented UV rotor profile and two-stage compression structure. Cast iron and stainless steel are used in the construction. The PM VSD motor and male rotor adopt an integrated shaft structure, so there is no coupling or gear transmission. This compact arrangement reduces efficiency loss and mechanical failure points.
Low noise and low vibration are achieved by removing motor, bearing, gear and coupling noise sources. The integrated PM VSD structure also saves floor space, which matters in dense production workshops.
This 185 kW class unit suits continuous manufacturing plants that need stable power air and clean instrument air. Typical duties include:
Sollant supports OEM/ODM customization. Project requirements can be discussed around the SLTT-V model, working pressure within 8–13 bar, air outlet size, and matched refrigerated dryer or precision filter configuration. Sollant was founded in 2004 and operates a 30,000 ㎡ facility with 20,000 units annual output.
A manufacturing plant in Indonesia purchased one 185 kW two-stage screw air compressor in 2020. The unit supplies continuous power air for pneumatic equipment, automated assembly lines, packaging machinery and spraying equipment, and clean instrument air for precision instruments and control systems.
After more than five years of continuous service, the plant reports lower electricity costs than with traditional single-stage compressors, stable pressure for 24/7 production, low failure rate in a hot and humid environment, and low noise and vibration.
It shows a 185 kW two-stage unit running in a hot, humid factory for over five years on continuous production. The application covered pneumatic equipment, assembly lines, packaging, spraying and instrument air.
It reduces the compression ratio per stage, internal leakage and bearing load. Two-stage PM VSD can increase displacement by nearly 15% and save up to 40% versus ordinary industrial frequency machines.
The SLTT-V series includes SLTT-22V, SLTT-30V, SLTT-37V, SLTT-45V, SLTT-55V, SLTT-75V, SLTT-90V, SLTT-110V, SLTT-132V, SLTT-160V, SLTT-185V, SLTT-220V and SLTT-250V.
Working pressure is 8–13 bar. Capacity range is 1.36–53.68 m³/min across the series. The exact model is selected against your air demand and duty cycle.
Sollant's related certification set includes CE for air compressors, CE for permanent magnet motors, EMC for the controller, PED verification for oil and air tanks, and ISO 14001 environmental management.
Yes. OEM/ODM support is available. Model, pressure within the series range, outlet size and matched air treatment can be specified for project requirements.
Sollant provides 24/7 engineering after-sales support and original spare parts through its international service team.
Send your required model, working pressure, capacity, site conditions and destination country to info@sollant.com. Tel or WhatsApp: +86 155-8905-3798. Address: No.215, Songri Center, Beihongqiao, Jiading District, Shanghai, China.
Discuss Your Project