{{ variable.name }}
Heavy-haul prime mover specified with a power take-off for tipper semi-trailer work in aggregate, coal and ore haulage.
This 6x4 tractor unit is configured for tipping work rather than dry van trunking: a power take-off is fitted for tipper semi-trailers, gearing moves to the heavy-haul band and the driveline is rated for repeated loaded cycles. Gross combination weight spans 25,000-60,000 kg within local axle-load rules, and the fifth wheel takes 10,000-16,000 kg at a 1,150-1,350 mm coupling height. A retarder or engine brake is specified for loaded descents from pit or quarry floors, and the trailer interface is confirmed with your tipper supplier before production.
| Vehicle type | Road tractor unit (prime mover) for semi-trailer haulage, tipper specification |
|---|---|
| Drive and tires | 6x4; 10 tubeless tires, 11R22.5, 12R22.5 or 315/80R22.5 |
| GVW / GCW | 16,000-25,000 kg / 25,000-60,000 kg by driveline and local axle-load rules |
| Fifth wheel | 10,000-16,000 kg load; 2 or 3.5 inch kingpin; coupling height 1,150-1,350 mm |
| Power take-off | Power take-off available for tipper semi-trailers; tipping system requirements confirmed at inquiry |
| Engine | Diesel, 6 cylinders in line, turbocharged and intercooled, 6.5-13 L, 240-560 hp, 900-2,600 N.m |
| Emission | Euro II to Euro V; Euro VI on request, matched to local fuel quality |
| Transmission | 9-16 forward speeds and 2 reverse; manual standard, AMT optional; clutch 395-430 mm |
| Axles and ratio | Front 6,500-7,500 kg; rear 13,000-16,000 kg each; ratio 4.11-5.29 heavy haul; differential locks optional |
| Brakes | Dual-circuit air brake, ABS standard, EBS optional, retarder or engine brake, spring parking brake |
| Fuel and electrics | 300-800 L aluminum or steel tank, single or twin; 24 V, trailer socket, GPS and telematics pre-wiring |
| Performance | 90-110 km/h with speed limiter; gradeability 20-35%; 28-40 L/100 km loaded; -30 to 50 C packages |
The range also includes 4x2 units for port drayage, 6x4 line-haul tractors with high-roof sleeper cabs and 6x6 off-road tractors for unpaved routes. For tipper work, options include differential locks, rear air suspension, forged aluminum wheels, roof deflector, tool box, spare wheel carrier, telematics and company livery. Cab choice covers day cab, sleeper cab and high-roof sleeper cab.
The ladder frame uses Q345 high-strength structural steel, 280-320 mm deep and 8 mm thick, with bolted cross members and reinforcement gussets for repeated loading. The welded steel cab carries electrophoretic primer and anti-corrosion coating. The fifth wheel is a cast or forged steel plate with hardened locking jaw and grease points, and the fuel tank is aluminum alloy or steel. Air and brake lines use hard-chrome-plated actuators, brass and stainless fittings and high-pressure rubber hoses.
Engine rating, gearbox and axle ratio are agreed against GCW, gradient and annual mileage, and the power take-off specification is matched to your tipper trailer requirements at inquiry. The cold package covers -30 C starting with a fuel heater, engine preheater and cab heater; the tropical package covers 50 C with a reinforced radiator, dust shield and high-capacity air conditioner. Left-hand and right-hand drive are both available.
The power take-off is specified for tipper semi-trailer work, driving the trailer tipping system from the tractor. Share your tipper trailer requirements and the PTO specification is confirmed before build.
A retarder or engine brake is recommended where loaded descents and pit ramps are routine. It holds the combination on long grades and reduces reliance on the service brakes.
Heavy-haul ratios of 4.11-5.29 suit mountain, quarry and heavy-haul work. Highway ratios of 2.85-4.11 suit operators running long paved legs between loads.
The fifth wheel is rated at 10,000-16,000 kg with a 2 inch or 3.5 inch kingpin, at a coupling height of 1,150-1,350 mm agreed with your trailer supplier.
About 30 days for orders under 20 units, with stock models shipping faster. Progress photos are shared at chassis, cab and final inspection.
Yes. Mixed tractor models and semi-trailers can be consolidated in one shipment under FOB, CIF or DAP terms, with invoice, packing list, bill of lading, certificate of origin and insurance.



Send tipper trailer type, tipping system requirements, payload per cycle, pit or road gradient and axle-load rules. Sales engineers confirm the PTO specification, axle ratio and fifth wheel interface before production.